Beetle® PBTS830F

注：该材料由 TEKNOR APEX 厂家直供，厂家技术人员进行生产指导，提供正规出场报告，相关检测报告等。

种类 :	PBT
品牌 :	Beetle®
用途 :

订购热线：021-58958519 13061808058(赵先生)

Beetle® PBTS830F 产品信息

基本信息
填料/增强材料	玻璃纤维增强材料, 30% 填料按重量
添加剂	阻燃性 2
特性	阻燃性
加工方法	注射成型

物理性能	额定值	单位制	测试方法
密度	1.71	g/cm³	ISO 1183
收缩率 ¹	0.80 到 1.4	%	内部方法

机械性能	额定值	单位制	测试方法
拉伸应力 (断裂)	130	MPa	ISO 527-2
拉伸应变 (断裂)	2.0	%	ISO 527-2
弯曲模量	9000	MPa	ISO 178
弯曲应力 ²	160	MPa	ISO 178

冲击性能	额定值	单位制	测试方法
悬壁梁缺口冲击强度	6.5	kJ/m²	ISO 180

热性能	额定值	单位制	测试方法
热变形温度
0.45 MPa, 未退火	> 200	°C	ISO 75-2/B
1.8 MPa, 未退火	190	°C	ISO 75-2/A

电气性能	额定值	单位制	测试方法
表面电阻率	1.0E+15	ohms	IEC 60093
体积电阻率	1.0E+17	ohms·cm	IEC 60093
介电强度 (3.00 mm)	15	kV/mm	IEC 60243-1
漏电起痕指数	300	V	IEC 60112

可燃性	额定值	单位制	测试方法
UL 阻燃等级 (1.50 mm)	V-0		内部方法
灼热丝易燃指数 (1.50 mm)	960	°C	IEC 60695-2-12
极限氧指数	38	%	ISO 4589-2

注射	额定值	单位制
干燥温度	120	°C
干燥时间	4.0	hr
料筒后部温度	240 到 260	°C
料筒中部温度	240 到 260	°C
料筒前部温度	240 到 260	°C
加工（熔体）温度	< 270	°C
模具温度	70.0 到 90.0	°C
注射速度	中等
螺杆转速	50 到 200	rpm

注射说明
Back pressure: LowInjection pressure: HighPBT materials are hygroscopic and very sensitive to moisture content during processing. Unlike many other materials, excessive moisture may not give rise to the appearance of splash marks on the surface of mouldings, but hydrolytic degradation of the melt can lead to significant impairment of properties, characterised most noticeably by embrittlement of the mouldings and reduced melt viscosity. Adequate pre-drying is therefore essential.Drying should ideally be carried out in a vacuum oven or a dehumidified air drier. The recommended drying time for dehumidified air dryers is 4 hours at 120°C. Drying times may need to be extended if the material has become very wet.

注射说明

Back pressure: LowInjection pressure: HighPBT materials are hygroscopic and very sensitive to moisture content during processing. Unlike many other materials, excessive moisture may not give rise to the appearance of splash marks on the surface of mouldings, but hydrolytic degradation of the melt can lead to significant impairment of properties, characterised most noticeably by embrittlement of the mouldings and reduced melt viscosity. Adequate pre-drying is therefore essential.Drying should ideally be carried out in a vacuum oven or a dehumidified air drier. The recommended drying time for dehumidified air dryers is 4 hours at 120°C. Drying times may need to be extended if the material has become very wet.

备注
1 .	Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).
2 .	Break

备注

1 .

Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

2 .

Break

在线客服

联系电话

021-58958519

13061808058(赵生)

微信客服